• Remove the AC power.
• Remove the battery.
• Remove the hinge cover.
• Remove the keyboard.
  

2.Locate the WLAN card.

3.Disconnect the two cables from the card.

 NOTE: 

You will find three cables for the wireless card. The third cable is for the new wireless standard not yet approved. However, this system can use the new technology when approved. 

4.Pull the two securing levers away from the card, and then remove the card.

5.Lift the WLAN card to a 45-degree angle.

6.Lift the WLAN card out of the slot.

1.Before removing the LCD:

• Remove the AC power.
• Remove the battery.
• Remove the SIM.
• Remove memory DIMM B.
• Remove the optical drive.
• Remove the hard drive.
• Remove the hinge cover.
  
• Remove the keyboard.
• Remove the Bluetooth® card.
• Remove the coin-cell battery.
• Remove memory DIMM A.
• Remove the WWAN card.
• Remove the WLAN card.
• Remove the LCD. 

2.Locate the LCD.

3.Remove the bumpers covering the screws.

4.Remove the six screws.

5.Push the LCD bezel out from the inside frame to release, then up and lift it off the frame.

6.Remove the eight frame screws from the LCD brackets.

7.Lift the LCD from the LCD backing.

8.Rotate the LCD to access the LCD cable on the back of the LCD.

9.Push in on the top LCD cable levers to release the cable connection, and then pull up on the bottom connection to release the cable.

10.Remove the LCD brackets from the LCD. 

NOTE: 

When replacing the LCD, you must move the two brackets to the replacement LCD. 

11.Slide the LCD brackets from the LCD.

12.Reverse the previous steps to assemble the LCD. pan>

• Remove the AC power.
• Remove the battery.
• Remove the hinge cover.
• Remove the keyboard.

2.Locate the LCD.

3.Disconnect all cables to the WWAN and WLAN cards if necessary.

4.Disconnect the video cable from the chassis.

5.Remove the four hinge screws from the back and bottom of the chassis.

6.Lift the LCD from the frame.

7.Reverse the previous steps to replace the LCD.

• Remove the AC power.
• Remove the battery.
• Remove the hinge cover.
• Remove the keyboard.
• Remove memory DIMM A.
  

2.Locate the WWAN card.

3.Disconnect the two cables from the WWAN card.

4.Pull the two securing levers away from the WWAN card, and then remove the card.

5.Lift the WWAN card to a 45-degree angle.

6.Lift the WWAN card out of the slot.

7.Reverse the previous steps to replace the WWAN card.

• Remove the AC power.
• Remove the battery.
• Remove the hinge cover.
• Remove the keyboard. 

2.Locate the memory DIMM.

3.Press out on the latches on both sides of the DIMM socket.

4.Pull the memory up to a 45-degree angle.

5.Remove the DIMM from the socket.

6.Reverse the previous steps to replace memory DIMM A.

• Remove the AC power.
• Remove the battery.
• Remove the hard drive.
• Remove the hinge cover.
• Remove the keyboard.
  

2.Locate the coin-cell battery.

3.Slide the coin-cell battery away from the LCD.

4.Disconnect the cable connection and lift the coin-cell battery from the system.

5.Reverse the previous steps to replace the coin-cell battery.

• Remove the AC power.
• Remove the battery.
• Remove the hinge cover.
• Remove the keyboard. 

2.Locate the Bluetooth wireless card.

3.Insert a scribe to release the clip holding the card.

4.Slide the Bluetooth wireless card away from the LCD.

5.Lift the Bluetooth wireless card from the system.

6.Disconnect the Bluetooth wireless card cable.

7.Reverse the previous steps to replace the Bluetooth wireless card.

• Remove the AC power.
• Remove the battery.
• Remove the hinge cover. 

2.Locate the keyboard.

3.Remove the screws holding the keyboard to the chassis.

4.Lift the keyboard and turn it away from the LCD.

5.Release the keyboard cable lock.

6.Release the ZIF connector to detach the cable and lift the keyboard from the system.

7. Reverse the previous steps to replace the keyboard.

Remove the battery.

2.Locate the hinge cover.

3.Insert a scribe into the hinge cover slot.

4.Pry up on the notch on the right side of the hinge cover.

5.Lift and remove the hinge cover from the chassis.

6.Reverse the previous steps to replace the hinge cover.